Re:Comagination Brak Flasher Install
Favoured: 0
|
|
|
TOPIC: Re:Comagination Brak Flasher Install
|
|
|
|
Comagination Brak Flasher Install 1 Year, 11 Months ago
|
|
|
Can anyone help me with the install on the brake unit? Headlight is plug and play. Have to figure out wires and placement for the brake unit.
|
|
|
|
Logged
|
|
|
|
|
|
The administrator has disabled public write access.
|
|
|
|
Re:Comagination Brak Flasher Install 1 Year, 11 Months ago
|
|
|
Not sure what type of brake unit your talking about but the wire harness is on the clutch side under the seat. Yellow is the brake light the blue is the tail light and that leaves the green and brown,right and left turn signals respectivly.
|
|
|
|
Logged
|
|
|
06 Midnight Silverado
*nothing shines like a star*
|
|
|
The administrator has disabled public write access.
|
|
|
|
Re:Comagination Brak Flasher Install 1 Year, 11 Months ago
|
|
|
|
|
|
|
Logged
|
|
|
|
|
|
The administrator has disabled public write access.
|
|
|
|
Re:Comagination Brak Flasher Install 1 Year, 11 Months ago
|
|
|
Here's brief install:
It’s EZ to install just 3 wires. Interrupt your vehicle’s power brake wire feed to lights (cut or disconnect it) and attached the VisiStop blue wire to the end going to the brake lights and the red wire to the brake switch. Then connect the black wire to the vehicle’s battery negative.
|
|
|
|
Logged
|
|
|
|
|
|
The administrator has disabled public write access.
|
|
|
|
Re:Comagination Brak Flasher Install 1 Year, 11 Months ago
|
|
|
Bump
|
|
|
|
Logged
|
|
|
|
|
|
The administrator has disabled public write access.
|
Erbman02 (User)
Platinum Boarder
Posts: 5492
|
|
Re:Comagination Brak Flasher Install 1 Year, 11 Months ago
|
|
|
the direction are on the web page. all you need to deal with is one wire on the bike, the yellow wire. cut the yellow, the blue connects to yellow on lamp side, the red connects to yellow on brake lever (switch) side, the black can go to any ground, it does not have to got directly to the battery ground, the entire bike metal is connected to battery ground. should be about a 5 min job with solder and heat shrink. Just so ya know, there are bulbs that do the same too without cutting wires.
|
|
|
|
Logged
|
|
|
|
|
|
The administrator has disabled public write access.
|
|
|
|
Re:Comagination Brak Flasher Install 1 Year, 11 Months ago
|
|
|
Thanks Erbman! I'm good with soldering but haven't used shrink wrap much. Do you use the soldering iron heat to shrink?
|
|
|
|
Logged
|
|
|
|
|
|
The administrator has disabled public write access.
|
Erbman02 (User)
Platinum Boarder
Posts: 5492
|
|
Re:Comagination Brak Flasher Install 1 Year, 11 Months ago
|
|
|
cigarette lighter. maybe a hair dryer if it can hot enough. And if you want a higher quality heat shrink use marine grade, but probably not necessary. just an option
|
|
|
|
Logged
|
|
|
|
|
|
The administrator has disabled public write access.
|
|
|
|
Re:Comagination Brak Flasher Install 1 Year, 11 Months ago
|
|
|
Have cigar torch that might be perfect
|
|
|
|
Logged
|
|
|
|
|
|
The administrator has disabled public write access.
|
|
|
|
Re:Comagination Brak Flasher Install 1 Year, 11 Months ago
|
|
BTW - Thanks Erbman for making this simple. I looked over the instructions that came with it and was way over complicating it! And thinking the LED had some special requirement.
|
|
|
|
Logged
|
|
|
|
|
|
The administrator has disabled public write access.
|
|
|
|
......................................................................
......................................................................
......................................................................
......................................................................
......................................................................
......................................................................
......................................................................
......................................................................
......................................................................
-->