Re:Bike will not start with choke - Road Star Forum

	Road Star Forum	Forum Threaded View Rules

Welcome, Guest
Please Login or Register. Lost Password?

Road Star Forum

Technical Corner

Jetting

Re:Bike will not start with choke

Favoured: 0

Page:
<< Start < Prev 1 2 Next > End >>

TOPIC: Re:Bike will not start with choke

Forum Tools

#232294

Transam1 (User)

Gold Boarder

Posts: 650

Bike will not start with choke 2 Years, 7 Months ago

Hey guys,
Since I re-jetted my bike I find that the thing will not start with the
choke at all. Before I could open the choke fully it would crank right
up and run. Now I find If I open the choke at any position it's a no go.
I have to give it a few twists of the throttle then manually hold it open
to keep it running. If I release the throttle it dies. After it's warm
no problems. Currently have 175 main, needle 3rd clip off soft seat and
the pms has been tried at 3 turns and 3 1/2 turns with no change. I'll try
2 1/2 turns today assuming a rich condition.I did pull the choke cable
out of the carb when I pulled the carb, ( just unscrewed the brass nut and
slide the cable right out of the carb )is it possible that I damaged something
in the cable ? It slide right back in. Any input would be appreciated, snow
is ready to fly and standing out there holding the throttle open for
10 minutes will suck.

Thanks,
Chris

Logged

The administrator has disabled public write access.

#232315

smhowse (Moderator)

Book em Dan-o!

Moderator

Posts: 3508

Re:Bike will not start with choke 2 Years, 7 Months ago
175 main seems a bit rich I always go back to the last thing I touched. If it ran ok before touching the carb recheck the carb. The choke cable assy is pretty simple but, can't hurt to check it again. BTW are your jets Minuki or Dyna? (difference in sizes) Steven

Logged

The administrator has disabled public write access.

#232332

Transam1 (User)

Gold Boarder

Posts: 650

Re:Bike will not start with choke 2 Years, 7 Months ago

Dyno jets which would be between a 157.5 and a 160 in mikuni.
Would the main effect start up though ?
I beleive that dynojet says their kit shoudn't effect
idle circuit. Hell, I don't know. I usually don't jack
with carbs because I always seem to bump into problems.
I know it's something simple just frustrating though.
If ya think of anything let me know.
Thanks,
Chris

smhowse wrote:
175 main seems a bit rich

I always go back to the last thing I touched. If it ran ok before touching the carb recheck the carb. The choke cable assy is pretty simple but, can't hurt to check it again.

BTW are your jets Minuki or Dyna? (difference in sizes)

Steven

Logged

Last Edit: 2009/10/21 16:12 By Transam1.

The administrator has disabled public write access.

#232333

BigBoyinMS (User)

I'm satisfied never being satisfied.

Platinum Boarder

Posts: 1705

Re:Bike will not start with choke 2 Years, 7 Months ago
I'm guessing that you bumped the float and got it out of adjustment. According to whether you have a BAK or modified airbox that jet sounds a little lean.

Logged

2006 Midnight

The administrator has disabled public write access.

#232388

Curt (Moderator)

Never to old to ride!

Moderator

Posts: 12515

Re:Bike will not start with choke 2 Years, 7 Months ago
The elevation for Brandon, MS is 482 feet I am at 432 feet at Dallas TX and I am running a 172.5 Mikuni, 3rd slot with two silver washers, 35 pilot. Your WAY to lean for you elevation try going to a 180 and move the clip to 4th slot. OR move the clip to the 5th slot and do the WOT.

Logged

My Site

Black Ice is Shiny, Black Ice is Deadly, Ya Wanna Ride My BlackIce?

The administrator has disabled public write access.

#232438

BigBoyinMS (User)

I'm satisfied never being satisfied.

Platinum Boarder

Posts: 1705

Re:Bike will not start with choke 2 Years, 7 Months ago

Curt wrote:
The elevation for Brandon, MS is 482 feet I am at 432 feet at Dallas TX and I am running a 172.5 Mikuni, 3rd slot with two silver washers, 35 pilot. Your WAY to lean for you elevation try going to a 180 and move the clip to 4th slot. OR move the clip to the 5th slot and do the WOT.

Hey Curt! I'm in Brandon,MS and he's in Grants, NM. 6,460 FT!
Hmmm I just noticed... you and I have the same setup.

Logged

Last Edit: 2009/10/21 22:44 By BigBoyinMS.

2006 Midnight

The administrator has disabled public write access.

#232505

nasomi (User)

Life's to important to take seriously.

Senior Boarder

Posts: 388

Re:Bike will not start with choke 2 Years, 7 Months ago
I have the same problem as the OP. However there's a lot here that is above my head. is there a good documentation about what all these numbers and such are so I can figure out how to solve my problems?

Logged

Jay

2001 Yamaha Road Star 1600
2004 Ford Excursion Diesel

The administrator has disabled public write access.

#232549

Transam1 (User)

Gold Boarder

Posts: 650

Re:Bike will not start with choke 2 Years, 7 Months ago
Yea, Im at 6460ft. Should I gather that all the other circuits will effect my choke in the morning ? Other than that the bike runs good. Thanks, Chris

Logged

The administrator has disabled public write access.

#232661

Curt (Moderator)

Never to old to ride!

Moderator

Posts: 12515

Re:Bike will not start with choke 2 Years, 7 Months ago
OH wonder how I made that mistake? DAAAA!

Logged

My Site

Black Ice is Shiny, Black Ice is Deadly, Ya Wanna Ride My BlackIce?

The administrator has disabled public write access.

#232716

BigBoyinMS (User)

I'm satisfied never being satisfied.

Platinum Boarder

Posts: 1705

Re:Bike will not start with choke 2 Years, 7 Months ago
Yes, actually every part of the carb works with every other part in your carb. Some more than others. Float level will affect everything and that's still my guess as to the problem. As far as your jetting, if you have a free breathing airbox then from what I read it should be close with a 175 DJ.

Logged

2006 Midnight

The administrator has disabled public write access.

Page:
<< Start < Prev 1 2 Next > End >>

Forum List

Technical Corner

Jetting

get the latest posts directly to your desktop

...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... -->

New Forum Posts
In: Technical Discussions, 5/26/2012, 21 replies Subject: advice on tail bags for a road trip. smokescreens: guys im gunna try my arse off to make it to the NC meet in oct. but i need to have more space for my cloths and such.im looking at this tailbag from saddlemen anyone else running it? it looks good and ... Latest reply, 5/27/2012 ironman: First trip on Roadie. Heading to Laconia, looking like the Beverly Hillbillys. Maybe actually used ...advice on tail bags for a road trip. 22 posts, last by: ironman In: Bike Talk, 5/26/2012, 15 replies Subject: Changing the shock spring Stevie: I'm going to lower my bike with the lowering links but it's been suggested to change the shock spring Is there a way to change it without a press? Latest reply, 5/27/2012 BC1955: No Stevie, I changed out the stock relay arm to the Baron's. I still have the stock dog bones but a ...Changing the shock spring 16 posts, last by: BC1955 In: Introductions, 5/27/2012, 3 replies Subject: Hello from TN. Georgeherrin: Hi new to the forum and thought I would let folks know a bit about me. I am happily married 5 children 13 to 25 and 6 grand children. I live in Hohenwald Tn. Pure country. My first license was a bike license. ... Latest reply, 5/27/2012 SKWEARpeg: Hey George,...... :welcome: .......from the panhandle of the Sunshine state. Affectionately known ...Hello from TN. 4 posts, last by: SKWEARpeg In: Non Motorcycle Topics, 5/26/2012, 23 replies Subject: Thank you, all who served. fireman922: It is not National BBQ Day. I am honored to thank all of you and the families who also served. (Stolen from FastJohnny) Latest reply, 5/27/2012 TReynolds: We can do and be who we are today only because of those who have served our country, THANK YOU!Thank you, all who served. 24 posts, last by: TReynolds In: Website General, 5/27/2012, 11 replies Subject: Members by location. Mudslide: I ride every day unless I know it's going to be pouring rain. I see Roadstars everywhere everyday. But there is no way to tell if any are members here. So......Admin, would it be possible to have a location ... Latest reply, 5/27/2012 PhatRJ: Are you guys reading my mind? Get out of my head! :P Was just thinking that about this weekend, that ...Members by location. 12 posts, last by: PhatRJ In: Electrical/Electronics, 5/26/2012, 14 replies Subject: So much for simple bencadenbach: I had a great idea to get rid of stock turn signals and use LED strips wrapped around the forks and all seemed pretty simple and strait forward and get a nice clean look. Well I got everything installed ... Latest reply, 5/27/2012 bencadenbach: Don't really know much about the electrical stuff. Whats a load equalizer and where could a guy find ...So much for simple 15 posts, last by: bencadenbach In: Miscellaneous, 5/26/2012, 14 replies Subject: this clinic has shown its true greatness yet again smokescreens: so as many of you know i have been dealing with a venders horrible customer service and overall operation issues and that has put my bike down at the start of the michigan 6-7 month riding season. and ... Latest reply, 5/27/2012 greyphart: Between the parts, advice and camaraderie the people here are what makes this site so great. Even members ...this clinic has shown its true greatness yet again 15 posts, last by: greyphart In: Bolt Ons, 5/26/2012, 17 replies Subject: New Handlebars - Stock Grips? alltimeqb: You guys might flog me but I just put a pair of Krome Werks Dyna Wide Glide handle bars on the R. Liked the looks of them on eBay, still warming up to 'em on the Roadie. But, what the heck are you ... Latest reply, 5/27/2012 alltimeqb: I bought a pair of black kury grips off ebay last night, didn't see your advice to go to republiccycle ...New Handlebars - Stock Grips? 18 posts, last by: alltimeqb In: Miscellaneous, 4/19/2012, 9 replies Subject: Hey Stevie... OK, just JB..: Saw a commercial last night on Discovery about a new show following a MC from San Diego. Heard anything about it/them? :huh: Latest reply, 5/27/2012 SKWEARpeg: We have a whole generation of people out there, who's entire life is comprised of their Smart phone, ...Hey Stevie... 10 posts, last by: SKWEARpeg In: Introductions, 5/26/2012, 22 replies Subject: Hello from the Region kozaturf: New to the clinic and wanted to say hi from "The Region" (NWI) Just picked up my Roadie on Monday and love it. Latest reply, 5/27/2012 Edge51: From B.C. that's Canada...where's NWI??? lol Hello from the Region 23 posts, last by: Edge51 In: Bolt Ons, 5/26/2012, 26 replies Subject: Flag mounts for 6"x9" Planet42: I recently joined PGR, and am interested in mounting 2 6"x9" flags to the back of my R - maybe off the license plate. Does anyone have any suggestions on what mounts are good and where I can get them? Latest reply, 5/27/2012 Darn: I made mine with the American flag up high and the other two are over the saddle bags, I can also mount ...Flag mounts for 6"x9" 27 posts, last by: Darn In: Bike Talk, 5/27/2012, 1 reply Subject: Interesting fact River: Here a while back we discussed the big question that if you change the pipes and put on a big air kit (or equivalent) will the fuel injected bikes (Roadies)run lean (or leaner) and no, they will not. Here ... Latest reply, 5/27/2012 Erbman02: when you reference a "point difference" is it a full point or decimal point?Interesting fact 2 posts, last by: Erbman02 In: Rides, Meets, Events, 5/14/2012, 80 replies Subject: WNC Meet and Greet theGRINDER: Ok guys, gals, friends and neighbors... time for a meet and greet with a garage day... I can't promise to get everything together myself, so I may need some help on this one... I will be working 7 10 hour ... Latest reply, 5/27/2012 Roger7886: Yea cold sucks... I always wanna go with the birds in the winter, I believe they are the smart ones :DWNC Meet and Greet 81 posts, last by: Roger7886 In: Non Motorcycle Topics, 5/27/2012, 10 replies Subject: It's 3:00 am ironman: just looked @ "who's on line" Thought I was the only one who's bat-crap crazy for being up at this hour, looking at a computer. GO TO BED !!!! Have a safe weekend everyone:laugh: :laugh: :laugh: Latest reply, 5/27/2012 Edge51: booIt's 3:00 am 11 posts, last by: Edge51 In: Non Motorcycle Topics, 5/25/2012, 26 replies Subject: I'm Torn Stevie: Walk Around Cuddy Fishing Boat Or Express Cruiser... The ... Latest reply, 5/27/2012 Edge51: LOL that is so true When I was buying my last one I called my insurance guy and told him I ...I'm Torn 27 posts, last by: Edge51 In: Bike Talk, 5/26/2012, 20 replies Subject: Road trip tool kit About_Time: I remember a recent thread on this subject, but after a half hour of worthless search results :censored:, I figured it was just easier to ask again. So here goes. I'm going to Americade next week and ... Latest reply, 5/27/2012 About_Time: VWH...thanks for posting this. I think I've seen it before, but it was one of those types of things ...Road trip tool kit 21 posts, last by: About_Time In: Bike Talk, 5/27/2012, 2 replies Subject: Road Star Ride Tomorrow Stevie: A few of us are heading up to Julian California on our Roadies in the morning It's a pretty popular weekend motorcycle destination If anybody's in the San Diego area tomorrow, come on up They got ... Latest reply, 5/27/2012 Stevie: Loading up as we speak First stop... Santa Ysabel for some breakfastRoad Star Ride Tomorrow 3 posts, last by: Stevie In: Electrical/Electronics, 5/26/2012, 7 replies Subject: Solar Pulse Battery Energy Power Charger? Ricohoc: http://www.fleetsafety.com/Solar-Pulse-Battery-Energy-Power-Charger-by-Pulsetech-506 Description: ... Latest reply, 5/27/2012 old dog: Says it's fine in the ad? Maintains new and used batteries in As-New condition indefinately. ...Solar Pulse Battery Energy Power Charger? 8 posts, last by: old dog In: Bike Talk, 5/26/2012, 7 replies Subject: Confused and a little frustrated. BK177V: I lost the chrome bezel that holds in the lens on the spot light on my 03 roadie. At first I thought it was a Cobra light bar, but I have had some people tell me that it is a factory Yamaha light bar. ... Latest reply, 5/27/2012 BK177V: I dont think they are Cobra. They do look like the ones in the above picture. I wouldnt mind buying 2 ...Confused and a little frustrated. 8 posts, last by: BK177V In: Rides, Meets, Events, 3/16/2012, 100 replies Subject: Central M&G, 2012 June 29,30, and July 1 fastjohnny: This is the "sign up sheet" for the central Meet & Greet (4th annual) to be held in the Anamosa, IA area. We may wind up staying closer to Cedar Rapids - way more hotels, but I don't know for sure just ... Latest reply, 5/27/2012 Darn: All are welcome! Come on up. I've got a couple of "Guest rooms" if needed, just ask EMU and Mandy, it's ...Central M&G, 2012 June 29,30, and July 1 101 posts, last by: Darn In: Bike Talk, 5/21/2012, 42 replies Subject: I have gone to the Darkside... TReynolds: Pirelli RT66 150/80/16 rear tire on Front at 40 psi Austone tire 175SR16 on rear at 38 psi No modifications for fitment Hand mounted both tires and installed myself (Cast Wheels). Front tire seated ... Latest reply, 5/27/2012 Darn: Dyna-beads are pretty easy to find, just google them. They are the best way to balance a tire, unless ...I have gone to the Darkside... 43 posts, last by: Darn In: Bike Talk, 5/8/2012, 38 replies Subject: My Project FF56: This will be about the ups and downs of buying my mystery bike. I call it that because I bought it from an estate sale, and have no info about it, but the price was great. So far it has been a challenge, ... Latest reply, 5/27/2012 Ricohoc: My Project 39 posts, last by: Ricohoc In: Electrical/Electronics, 5/25/2012, 18 replies Subject: Rear tail/brake light lens FF56: Does anyone know where I can find a clear tail/brake light lens for a 2000 R, I just installed a red LED tail light and turn signals, found clear turn signal lens, but I seem to not be looking in the ... Latest reply, 5/27/2012 Ricohoc: Rear tail/brake light lens 19 posts, last by: Ricohoc In: Technical Discussions, 5/26/2012, 2 replies Subject: where does the hoses go? zulu: ok i know im getting old but seeing as i have had the bike in bits for the winter ,can some one kick me up the arse and tell me where the two hoses go from the back of the air box....xv1600 99-model,i ... Latest reply, 5/27/2012 zulu: your a gentleman and a scolar ...many thanks old boy,where does the hoses go? 3 posts, last by: zulu In: Tech Tips, 5/26/2012, 6 replies Subject: Engine teardown video gearjammer: For those of you who have considered an engine teardown for whatever reason, but didn't want to pull the trigger. Whether it was due to a lack of confidence in the unknown or just like to watch someone ... Latest reply, 5/27/2012 Spydr: Helps to see it done at least once, right?Engine teardown video 7 posts, last by: Spydr In: Bolt Ons, 5/24/2012, 13 replies Subject: Do I really need push & pull cables? DropkickFace: Heard somewhere you only need 1? How's that? Pros? Cons? James Latest reply, 5/27/2012 Booster: If running a HSR carb the push don't work (for me anyway).Do I really need push & pull cables? 14 posts, last by: Booster In: Maintenance, 5/25/2012, 12 replies Subject: I messed up the Barnett conversion some how espressodude: Well I changed everything out and did as the instructions said to, I think. I don't think the clutch is engaging, when the bike is in gear pull the clutch handle and the wheel keeps on a turning. It may ... Latest reply, 5/26/2012 Greysnake: Glad it worked out and your clutch will have a better feel to it.:)I messed up the Barnett conversion some how 13 posts, last by: Greysnake In: Miscellaneous, 5/26/2012, 11 replies Subject: Let the summer begin...(not quite) h_unzeki: Took the bike to my mechanic the other day to have my Progressive Spring mounted (finally)- along with a few other mind details. Called him this morning to see if my baby was done and got ahold of his ... Latest reply, 5/26/2012 blue star: Time for a new mechanic.:angry:Let the summer begin...(not quite) 12 posts, last by: blue star In: Introductions, 5/24/2012, 35 replies Subject: Hello from Kentucky myxlr: nice to be here i ride a 2008 silverado Latest reply, 5/26/2012 Edge51: from B.C. Hello from Kentucky 36 posts, last by: Edge51 In: Maintenance, 5/25/2012, 15 replies Subject: Brake pads slyguy: I'm looking to replace both front and rear brake pads. I hear EBC Double H Sintered are good. Can I get part numbers for both? TIA! Latest reply, 5/26/2012 mkayx*: they look every close to the galfer i did not think there is a diff between an 2000 and an 02Brake pads 16 posts, last by: mkayx

New Forum Posts

In: Technical Discussions, 5/26/2012, 21 replies
Subject: advice on tail bags for a road trip.
smokescreens: guys im gunna try my arse off to make it to the NC meet in oct. but i need to have more space for my cloths and such.im looking at this tailbag from saddlemen anyone else running it? it looks good and ...

Latest reply, 5/27/2012
ironman: First trip on Roadie. Heading to Laconia, looking like the Beverly Hillbillys. Maybe actually used ...advice on tail bags for a road trip.

22 posts, last by:

ironman

In: Bike Talk, 5/26/2012, 15 replies
Subject: Changing the shock spring
Stevie: I'm going to lower my bike with the lowering links but it's been suggested to change the shock spring Is there a way to change it without a press?

Latest reply, 5/27/2012
BC1955: No Stevie, I changed out the stock relay arm to the Baron's. I still have the stock dog bones but a ...Changing the shock spring

16 posts, last by:

BC1955

In: Introductions, 5/27/2012, 3 replies
Subject: Hello from TN.
Georgeherrin: Hi new to the forum and thought I would let folks know a bit about me. I am happily married 5 children 13 to 25 and 6 grand children. I live in Hohenwald Tn. Pure country. My first license was a bike license. ...

Latest reply, 5/27/2012
SKWEARpeg: Hey George,...... :welcome: .......from the panhandle of the Sunshine state. Affectionately known ...Hello from TN.

4 posts, last by:

SKWEARpeg

In: Non Motorcycle Topics, 5/26/2012, 23 replies
Subject: Thank you, all who served.
fireman922: It is not National BBQ Day. I am honored to thank all of you and the families who also served. (Stolen from FastJohnny)

Latest reply, 5/27/2012
TReynolds: We can do and be who we are today only because of those who have served our country, THANK YOU!Thank you, all who served.

24 posts, last by:

TReynolds

In: Website General, 5/27/2012, 11 replies
Subject: Members by location.
Mudslide: I ride every day unless I know it's going to be pouring rain. I see Roadstars everywhere everyday. But there is no way to tell if any are members here. So......Admin, would it be possible to have a location ...

Latest reply, 5/27/2012
PhatRJ: Are you guys reading my mind? Get out of my head! :P Was just thinking that about this weekend, that ...Members by location.

12 posts, last by:

PhatRJ

In: Electrical/Electronics, 5/26/2012, 14 replies
Subject: So much for simple
bencadenbach: I had a great idea to get rid of stock turn signals and use LED strips wrapped around the forks and all seemed pretty simple and strait forward and get a nice clean look. Well I got everything installed ...

Latest reply, 5/27/2012
bencadenbach: Don't really know much about the electrical stuff. Whats a load equalizer and where could a guy find ...So much for simple

15 posts, last by:

bencadenbach

In: Miscellaneous, 5/26/2012, 14 replies
Subject: this clinic has shown its true greatness yet again
smokescreens: so as many of you know i have been dealing with a venders horrible customer service and overall operation issues and that has put my bike down at the start of the michigan 6-7 month riding season. and ...

Latest reply, 5/27/2012
greyphart: Between the parts, advice and camaraderie the people here are what makes this site so great. Even members ...this clinic has shown its true greatness yet again

15 posts, last by:

greyphart

In: Bolt Ons, 5/26/2012, 17 replies
Subject: New Handlebars - Stock Grips?
alltimeqb: You guys might flog me but I just put a pair of Krome Werks Dyna Wide Glide handle bars on the R*. Liked the looks of them on eBay, still warming up to 'em on the Roadie. But, what the heck are you ...

Latest reply, 5/27/2012
alltimeqb: I bought a pair of black kury grips off ebay last night, didn't see your advice to go to republiccycle ...New Handlebars - Stock Grips?

18 posts, last by:

alltimeqb

In: Miscellaneous, 4/19/2012, 9 replies
Subject: Hey Stevie...
OK, just JB..: Saw a commercial last night on Discovery about a new show following a MC from San Diego. Heard anything about it/them? :huh:

Latest reply, 5/27/2012
SKWEARpeg: We have a whole generation of people out there, who's entire life is comprised of their Smart phone, ...Hey Stevie...

10 posts, last by:

SKWEARpeg

In: Introductions, 5/26/2012, 22 replies
Subject: Hello from the Region
kozaturf: New to the clinic and wanted to say hi from "The Region" (NWI) Just picked up my Roadie on Monday and love it.

Latest reply, 5/27/2012
Edge51: From B.C. that's Canada...where's NWI??? lol Hello from the Region

23 posts, last by:

Edge51

In: Bolt Ons, 5/26/2012, 26 replies
Subject: Flag mounts for 6"x9"
Planet42: I recently joined PGR, and am interested in mounting 2 6"x9" flags to the back of my R* - maybe off the license plate. Does anyone have any suggestions on what mounts are good and where I can get them?

Latest reply, 5/27/2012
Darn: I made mine with the American flag up high and the other two are over the saddle bags, I can also mount ...Flag mounts for 6"x9"

27 posts, last by:

Darn

In: Bike Talk, 5/27/2012, 1 reply
Subject: Interesting fact
River: Here a while back we discussed the big question that if you change the pipes and put on a big air kit (or equivalent) will the fuel injected bikes (Roadies)run lean (or leaner) and no, they will not. Here ...

Latest reply, 5/27/2012
Erbman02: when you reference a "point difference" is it a full point or decimal point?Interesting fact

2 posts, last by:

Erbman02

In: Rides, Meets, Events, 5/14/2012, 80 replies
Subject: WNC Meet and Greet
theGRINDER: Ok guys, gals, friends and neighbors... time for a meet and greet with a garage day... I can't promise to get everything together myself, so I may need some help on this one... I will be working 7 10 hour ...

Latest reply, 5/27/2012
Roger7886: Yea cold sucks... I always wanna go with the birds in the winter, I believe they are the smart ones :DWNC Meet and Greet

81 posts, last by:

Roger7886

In: Non Motorcycle Topics, 5/27/2012, 10 replies
Subject: It's 3:00 am
ironman: just looked @ "who's on line" Thought I was the only one who's bat-crap crazy for being up at this hour, looking at a computer. GO TO BED !!!! Have a safe weekend everyone:laugh: :laugh: :laugh:

Latest reply, 5/27/2012
Edge51: booIt's 3:00 am

11 posts, last by:

Edge51

In: Non Motorcycle Topics, 5/25/2012, 26 replies
Subject: I'm Torn
Stevie: Walk Around Cuddy Fishing Boat Or Express Cruiser... The ...

Latest reply, 5/27/2012
Edge51: LOL that is so true When I was buying my last one I called my insurance guy and told him I ...I'm Torn

27 posts, last by:

Edge51

In: Bike Talk, 5/26/2012, 20 replies
Subject: Road trip tool kit
About_Time: I remember a recent thread on this subject, but after a half hour of worthless search results :censored:, I figured it was just easier to ask again. So here goes. I'm going to Americade next week and ...

Latest reply, 5/27/2012
About_Time: VWH...thanks for posting this. I think I've seen it before, but it was one of those types of things ...Road trip tool kit

21 posts, last by:

About_Time

In: Bike Talk, 5/27/2012, 2 replies
Subject: Road Star Ride Tomorrow
Stevie: A few of us are heading up to Julian California on our Roadies in the morning It's a pretty popular weekend motorcycle destination If anybody's in the San Diego area tomorrow, come on up They got ...

Latest reply, 5/27/2012
Stevie: Loading up as we speak First stop... Santa Ysabel for some breakfastRoad Star Ride Tomorrow

3 posts, last by:

Stevie

In: Electrical/Electronics, 5/26/2012, 7 replies
Subject: Solar Pulse Battery Energy Power Charger?
Ricohoc: http://www.fleetsafety.com/Solar-Pulse-Battery-Energy-Power-Charger-by-Pulsetech-506 Description: ...

Latest reply, 5/27/2012
old dog: Says it's fine in the ad? Maintains new and used batteries in As-New condition indefinately. ...Solar Pulse Battery Energy Power Charger?

8 posts, last by:

old dog

In: Bike Talk, 5/26/2012, 7 replies
Subject: Confused and a little frustrated.
BK177V: I lost the chrome bezel that holds in the lens on the spot light on my 03 roadie. At first I thought it was a Cobra light bar, but I have had some people tell me that it is a factory Yamaha light bar. ...

Latest reply, 5/27/2012
BK177V: I dont think they are Cobra. They do look like the ones in the above picture. I wouldnt mind buying 2 ...Confused and a little frustrated.

8 posts, last by:

BK177V

In: Rides, Meets, Events, 3/16/2012, 100 replies
Subject: Central M&G, 2012 June 29,30, and July 1
fastjohnny: This is the "sign up sheet" for the central Meet & Greet (4th annual) to be held in the Anamosa, IA area. We may wind up staying closer to Cedar Rapids - way more hotels, but I don't know for sure just ...

Latest reply, 5/27/2012
Darn: All are welcome! Come on up. I've got a couple of "Guest rooms" if needed, just ask EMU and Mandy, it's ...Central M&G, 2012 June 29,30, and July 1

101 posts, last by:

Darn

In: Bike Talk, 5/21/2012, 42 replies
Subject: I have gone to the Darkside...
TReynolds: Pirelli RT66 150/80/16 rear tire on Front at 40 psi Austone tire 175SR16 on rear at 38 psi No modifications for fitment Hand mounted both tires and installed myself (Cast Wheels). Front tire seated ...

Latest reply, 5/27/2012
Darn: Dyna-beads are pretty easy to find, just google them. They are the best way to balance a tire, unless ...I have gone to the Darkside...

43 posts, last by:

Darn

In: Bike Talk, 5/8/2012, 38 replies
Subject: My Project
FF56: This will be about the ups and downs of buying my mystery bike. I call it that because I bought it from an estate sale, and have no info about it, but the price was great. So far it has been a challenge, ...

Latest reply, 5/27/2012
Ricohoc: My Project

39 posts, last by:

Ricohoc

In: Electrical/Electronics, 5/25/2012, 18 replies
Subject: Rear tail/brake light lens
FF56: Does anyone know where I can find a clear tail/brake light lens for a 2000 R*, I just installed a red LED tail light and turn signals, found clear turn signal lens, but I seem to not be looking in the ...

Latest reply, 5/27/2012
Ricohoc: Rear tail/brake light lens

19 posts, last by:

Ricohoc

In: Technical Discussions, 5/26/2012, 2 replies
Subject: where does the hoses go?
zulu: ok i know im getting old but seeing as i have had the bike in bits for the winter ,can some one kick me up the arse and tell me where the two hoses go from the back of the air box....xv1600 99-model,i ...

Latest reply, 5/27/2012
zulu: your a gentleman and a scolar ...many thanks old boy,where does the hoses go?

3 posts, last by:

zulu

In: Tech Tips, 5/26/2012, 6 replies
Subject: Engine teardown video
gearjammer: For those of you who have considered an engine teardown for whatever reason, but didn't want to pull the trigger. Whether it was due to a lack of confidence in the unknown or just like to watch someone ...

Latest reply, 5/27/2012
Spydr: Helps to see it done at least once, right?Engine teardown video

7 posts, last by:

Spydr

In: Bolt Ons, 5/24/2012, 13 replies
Subject: Do I really need push & pull cables?
DropkickFace: Heard somewhere you only need 1? How's that? Pros? Cons? James

Latest reply, 5/27/2012
Booster: If running a HSR carb the push don't work (for me anyway).Do I really need push & pull cables?

14 posts, last by:

Booster

In: Maintenance, 5/25/2012, 12 replies
Subject: I messed up the Barnett conversion some how
espressodude: Well I changed everything out and did as the instructions said to, I think. I don't think the clutch is engaging, when the bike is in gear pull the clutch handle and the wheel keeps on a turning. It may ...

Latest reply, 5/26/2012
Greysnake: Glad it worked out and your clutch will have a better feel to it.:)I messed up the Barnett conversion some how

13 posts, last by:

Greysnake

In: Miscellaneous, 5/26/2012, 11 replies
Subject: Let the summer begin...(not quite)
h_unzeki: Took the bike to my mechanic the other day to have my Progressive Spring mounted (finally)- along with a few other mind details. Called him this morning to see if my baby was done and got ahold of his ...

Latest reply, 5/26/2012
blue star: Time for a new mechanic.:angry:Let the summer begin...(not quite)

12 posts, last by:

blue star

In: Introductions, 5/24/2012, 35 replies
Subject: Hello from Kentucky
myxlr: nice to be here i ride a 2008 silverado

Latest reply, 5/26/2012
Edge51: from B.C. Hello from Kentucky

36 posts, last by:

Edge51

In: Maintenance, 5/25/2012, 15 replies
Subject: Brake pads
slyguy: I'm looking to replace both front and rear brake pads. I hear EBC Double H Sintered are good. Can I get part numbers for both? TIA!

Latest reply, 5/26/2012
mkayx: they look every close to the galfer i did not think there is a diff between an 2000 and an 02Brake pads

16 posts, last by:

mkayx

The Road Star Clinic is a collaborative community of riders who archive and publish user contributed technical data about Yamaha Road Star motorcycles.

We also sponsor the creation and support of other community websites similar to our own. Inquiries about availability of a website for your community can be submitted to us via any "Contact Us" option on the Clinic.