|
|
|
Starting my 31 tooth this weekend 3 Months, 3 Weeks ago
|
|
Alright I am getting my parts in today and I wanted to go over things to make sure I got everything.
31 tooth pulley: I have a 36 mm socket, torque specs are 61 lbs, lock tite, shouldn't need a new belt, and I am assuming I'll need to tighten it up though...? I also have an impact wrench for removal.
Dyna 3000: The main thing a lot of people told me was to be sure and cut out a window for the switches.
Which brings me to a question. Can anyone recommend what settings I should use on it? I have an 03 1600, BAK, and VH longshots. I dont know what I should set all switches to. I found the chart in the tech section but it didnt really say what to set them to for certain mods...
Thanks everyone. |
|
|
|
 Logged
|
|
|
Sig Pic deleted - larger than 450 pixels and 50 KB
|
|
|
The administrator has disabled public write access.
|
Questcap (User)
Platinum Boarder
Posts: 3209
|
|
Re:Starting my 31 tooth this weekend 3 Months, 3 Weeks ago
|
|
dingo,
It may not work for you, but did on both of my R*s. I was able to just put the wheel all the way back in the adjustment slots on the swingarm, and got the right tension both times. I then did some minor tweeking to assure alignment.
As for the Dyna. It's pretty much set-it and forget-it, so the cutting of a window in the rubber battery box is totally optional, and I didn't.
It's been some time, so I don't remember all the switches, but on a 1600, setting for a 5,000 rpm limit with 34 degrees of advance has been the most common recommendation here on the Clinic, and so, that's what I went with, and it works just fine for me.
Others? |
|
|
|
Logged
|
|
|
Sig pic deleted - larger than 450 pixels and 50 kb
|
|
|
The administrator has disabled public write access.
|
|
|
|
Re:Starting my 31 tooth this weekend 3 Months, 3 Weeks ago
|
|
Bump....
on the 31 tooth adjustment as stated by Questcap
Dyna 3000 switches set @ 5,000 rpm and 34a for a 1600, ride it like you stole it...
Samson |
|
|
|
Logged
|
|
|
The administrator has disabled public write access.
|
|
|
|
Re:Starting my 31 tooth this weekend 3 Months, 3 Weeks ago
|
|
Thank you gentlemen! I will start this project this weekend and let yall know how it goes. 
I am anxious to see/feel the results  |
|
|
|
Logged
|
|
|
Sig Pic deleted - larger than 450 pixels and 50 KB
|
|
|
The administrator has disabled public write access.
|
|
|
|
Re:Starting my 31 tooth this weekend 3 Months, 3 Weeks ago
|
|
I did installed the 31 on my 1600.I did not like it at all.it makes the bike to fuzzy,i have the dyna 3000 on.the dyna with the 33 is a smooth ride,it takes a longer to reach the high rpms.with the 31 feels like I don't have a dyna on.
I thought the acceleration will improve drastically but it didn't,accelarates quicker but also you reach your top rpms quicker.
I going to put the 33 back this weekend and sale the 31 on ebay.
The thing with the pulleys is about taste, I prefer stay longer on the gear than shift constantly |
|
|
|
Logged
|
|
|
The administrator has disabled public write access.
|
|
|
|
Re:Starting my 31 tooth this weekend 3 Months, 3 Weeks ago
|
|
|
Well I havnt quite got a chance to try it out yet, but I am eager to get my opinion on it.
|
|
|
|
Logged
|
|
|
Sig Pic deleted - larger than 450 pixels and 50 KB
|
|
|
The administrator has disabled public write access.
|
|
|
|
Re:Starting my 31 tooth this weekend 3 Months, 3 Weeks ago
|
|
I did installed the 31 on my 1600.I did not like it at all.it makes the bike to fuzzy,i have the dyna 3000 on.the dyna with the 33 is a smooth ride,it takes a longer to reach the high rpms.with the 31 feels like I don't have a dyna on.
I thought the acceleration will improve drastically but it didn't,accelarates quicker but also you reach your top rpms quicker.
I going to put the 33 back this weekend and sale the 31 on ebay.
The thing with the pulleys is about taste, I prefer stay longer on the gear than shift constantly
because yer running too lean is why yer fuzzy.... yer demanding more fuel usage with the 31 tooth,
run a main jet #190 dj or a mikuni main #180 on e-clip #2 second with an after market airbox try a mikuni main #195 same needle setting. |
|
|
|
Logged
|
|
|
The administrator has disabled public write access.
|
Questcap (User)
Platinum Boarder
Posts: 3209
|
|
Re:Starting my 31 tooth this weekend 3 Months, 3 Weeks ago
|
|
I wanted the 31 tooth for two reasons. First, I do an awful lot of back-road cruising at between 35 and 45, and I was forever shifting up and down between third and fourth gears. I hated it.
With the 31 tooth, I can get to 4th, and just leave it there. 
Second, I thought it required just a bit more clutch slippage to launch than I was liking, so I knew I'd get a quicker and easier launch with the 31, and I most certainly do.
I didn't get any more vibration, or less, by switching pulleys, and gas mileage didn't appear to be affected in the least... so, I've been very happy with the conversion. I also put a Speedo-Healer on both bikes and set it for an 11% conversion, and they're spot-on!  |
|
|
|
Logged
|
|
|
Sig pic deleted - larger than 450 pixels and 50 kb
|
|
|
The administrator has disabled public write access.
|
|
|
|
Re:Starting my 31 tooth this weekend 3 Months, 3 Weeks ago
|
|
I didn't even think of the speedo being off now!  About how many MPH's is it off now without fixing it?
I do a mixture of riding (backroads and highway) but it drives me nuts having to shift all the time so I think I will be happy with it. |
|
|
|
Logged
|
|
|
Sig Pic deleted - larger than 450 pixels and 50 KB
|
|
|
The administrator has disabled public write access.
|
|
|
|
Re:Starting my 31 tooth this weekend 3 Months, 3 Weeks ago
|
|
I used to have to shift a lot on back roads as well but with the 3000 and the HSR 45 I can accelerate quite well from 45 mph in 5th gear. If I am in 4th on the back road I don't have to go down to 3rd any more and that is with stock pulleys. |
|
|
|
Logged
|
|
|
My Site
Black Ice is Shiny, Black Ice is Deadly, Ya Wanna Ride My BlackIce?
|
|
|
The administrator has disabled public write access.
|
|
Favoured: 0
