Make your own floor board pegs
Written by Jack Allen (BIGJCA)
Saturday, 10 July 2004
Chrome-plated Adjustable-mount Fold-up Foot Pegs, Any Style
Pair ZX064282U $24.99
¼ inch square tubing, 3 ft piece $4.25
2 - 10/32in x 1in 1 1/4in bolts with screw head with nylon ring nut (for each side)
1 - ¼ in x 1in bolt with nylon ring nut (for each side)
Remove floorboard pad.
Measure width of floorboard (approx. 4in) and length of peg from JC Whitney from nut into peg (approx. 1 ½ in).
Cut square pipe 5 ½ in long.
Drill 2 - 10/32in holes to attach to existing holes in floorboard.
Drill 1 - ¼in hole for peg bolt.
Attach cut square pipe with 2 bolts under floorboard.
Attach peg with bolt.
Hope this helps,
Questions should be asked in our forum (Use discuss link below).
The forum is very active and you stand a good chance of getting your questions
answered there. If you would like to leave feedback
for the author, or have additional information you think will benefit others, please use
the comment section at the bottom of this page.
Discuss this article on the forums. (5 posts)
This information and procedure is provided
as a courtesy and is for informational purposes only.
Neither the publishers nor the authors
accept any responsibility for the accuracy, applicability, or
suitability of this procedure. You assume all risks associated
with the use of this information. NEITHER THE PUBLISHERs NOR THE AUTHORs
SHALL IN ANY EVENT BE LIABLE FOR ANY DIRECT, INDIRECT, PUNITIVE, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, OF ANY NATURE ARISING OUT OF OR IN ANY WAY
CONNECTED WITH THE USE OR MISUSE OF THIS INFORMATION OR LACK OF INFORMATION.
Any type of modification or service work on your motorcycle should
be performed by a
If performed incorrectly,
this procedure may
endanger the safety of you and others
on your motorcycle and possibly
invalidate your manufacturer’s warranty.
Quote this article on your site | Views: 30059
|Written by CCR, on 08-13-2010 19:52 |
Are You sure you don't mean 1/2 inch square tube? Kinda hard to drill a 1/4 hole in 1/4 tubing. Not trying to be a smart a$$ because I bought some pegs just to do this mod and my square stock that attaches the pegs to the u clamps is at least 1/2 inch. Just wanna make sure I'm looking at this right. Thanks, Chris
Written by Ghost Rider, on 11-01-2009 10:34
What a good idea.I`m over 6ft tall and have been looking for a solution to my highway problem. Thanks
|You just saved me 427.99|
Written by 031600_kmh, on 04-08-2008 19:59
am so glad i came here. have 03 1600 road star and have crashbars on it but don't like the highway peg's. competition accessories.com has heelrest and they start at 427.99 two 500.00.your Idea is great and will work. thank you
Only registered users can write comments.
Please login or register.
Powered by AkoComment Tweaked Special Edition v.1.4.6
AkoComment © Copyright 2004 by Arthur Konze - www.mamboportal.com
All right reserved
Copyright 2003-2007 Road Star Clinic and its respective authors.
The Road Star Clinic
is a collaborative community of riders who archive and publish user contributed technical
data about Yamaha Road Star motorcycles.
We also sponsor the creation and support of other community websites similar to our own. Inquiries
about availability of a website for your community can be submitted to us via any "Contact Us" option
on the Clinic.
Road Star Clinic is sponsored by the folks at MLSHomeQuest.com