I discovered a neat way to clean up the ugly black neck area of the Road Star. I came up with this idea when I installed a new custom headlight on my roadie, With the stock headlight housing removed it really exposed that area , so I came up with this, I installed a Yamaha chrome push rod tube cover over the neck! Snaps right on like it was made for it!
Questions should be asked in our forum (Use discuss link below).
The forum is very active and you stand a good chance of getting your questions
answered there. If you would like to leave feedback
for the author, or have additional information you think will benefit others, please use
the comment section at the bottom of this page.
Discuss this article on the forums. (0 posts)
This information and procedure is provided
as a courtesy and is for informational purposes only.
Neither the publishers nor the authors
accept any responsibility for the accuracy, applicability, or
suitability of this procedure. You assume all risks associated
with the use of this information. NEITHER THE PUBLISHERs NOR THE AUTHORs
SHALL IN ANY EVENT BE LIABLE FOR ANY DIRECT, INDIRECT, PUNITIVE, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, OF ANY NATURE ARISING OUT OF OR IN ANY WAY
CONNECTED WITH THE USE OR MISUSE OF THIS INFORMATION OR LACK OF INFORMATION.
Any type of modification or service work on your motorcycle should
be performed by a
If performed incorrectly,
this procedure may
endanger the safety of you and others
on your motorcycle and possibly
invalidate your manufacturer’s warranty.
Quote this article on your site | Views: 30205
Written by Fidel, on 02-29-2012 12:03
Good suggestion. I wondering what part is the chrome piece you have under the headlight. Looking to clean up the front end a little.
Written by windy, on 02-24-2012 06:17
|Written by BrooklynBiker, on 11-15-2011 05:51 |
Yamaha chrome push rod tube cover over the neck! Snaps right on like it was made for it!
Do you have a part number??
|Custom headlight re-wiring|
Written by hydra2172, on 08-11-2011 17:58
Hi Guy's I would like to install a custom headlight on my 06 R* classic the one I like Chrome Billet Tri-Bar Headlight 5.75"x8" long.
But before buying it' I looked inside the original headlight by removeing the front cover and there is quite a bit of wiring in there? if I go to the custom light, Can the excess wiring go into the bucket or will it just be exposed be-hide the light? I'm not sure what to do with all that wire.
|wHERE DID YOU GET THE COVERS|
Written by Carl6121, on 06-24-2009 16:16
WHERE DID YOU GET THE PUSHROD COVERS CANT FIND THEM ANY WERE
|kuryakn top cover|
Written by bobby2407, on 02-03-2009 10:21
i wonder if the kurykn toa tappet covers will fit at the top and bottom of the neck cover
|front neck cover|
Written by bobby2407, on 02-02-2009 12:35
does anyone have a chrome pushrod cover
Written by GOOSE915, on 01-13-2009 09:39
I am wanting to put chrome forks on my 99 Roadie and am wondering if anyone knows whether chrome forks off of newer Roadie will work on my older one? Any input is greatly appreciated.
|Written by huskerbob, on 12-29-2008 17:42 |
Great tip thank you
|Written by ZZ, on 06-02-2007 21:22 |
Here's one, has anyone ever come across and springers for roadies. Man, I think springers look so retro And would like to put a set on mine. I can get them from a Harley shop, but thinking It would be a lot of fab. I would be willing to try it but think I should explore all my options before going there. This would mean new wheels and brake mounts, the whole works. What do you think? ZZ
Only registered users can write comments.
Please login or register.
Powered by AkoComment Tweaked Special Edition v.1.4.6
AkoComment © Copyright 2004 by Arthur Konze - www.mamboportal.com
All right reserved